npn silicon planar transistor BF370R to-92 bec low level am p lifier transistor. absolute maximum ratings description value unit collector -base voltage vcbo 40 v collector -emitter voltage vceo 15 v emitter base voltage vebo 4.5 v collector current (continuous) ic 100 ma power dissipation @ ta=25 deg c pd 500 mw derate above 25 deg c 4.0 mw/deg c operating and storage junction tj, tstg -55 to +150 deg c temperature range lead temperature for soldering 1/16" tl 260 deg c from body for 10 seconds. thermal resistance junction to case rth (j-c) 83.3 deg c/w junction to ambient rth (j-a) 200 deg c/w electrical characteristics (ta=25 deg c unless otherwise specified) description symbol test condition min typ max unit collector -base voltage vcbo ic=100ua, ie=0 40 - - v collector -emitter voltage vceo ic=100ua, ib=0 15 - - v emitter base voltage vebo ie=100ua, ic=0 4.5 - - v collector cut off current icbo vcb=20v, ie=0 - - 400 na ta=125 deg c vcb=15v, ie=0 - - 30 ua emitter cut off current iebo veb=2v, ic=0 - - 100 na dc current gain hfe ic=10ma,vce=1v 40 - - dynamic characteristics transistors frequency ft ic=10ma,vce=10v 500 - - mhz ic=40ma,vce=10v 490 - mhz collector capacitance cc vcb=10v, ie=0, f=1mhz pf emitter capacitance ce veb=1v, ic= ic=0, f=1mhz - - 4.5 pf feedback capacitance cre ic=0, vce=10v, f=1mhz pf interference voltage for k=1% gv v(int) rms mv typ 2.2 typ 1.6 typ 120 continental device india limited data sheet page 1 of 3 continental device india limited an iso/ts 16949, iso 9001 and iso 14001 certified company
to-92 transistors on tape and ammo pack to-92 plastic package to-92 bulk to-92 t&a 1k/polybag 2k/ammo box 200 gm/1k pcs 645 gm/2k pcs 3" x 7.5" x 7.5" 12.5" x 8" x 1.8" 5.0k 2.0k 17" x 15" x 13.5" 17" x 15" x 13.5" 80.0k 32.0k 23 kgs 12.5 kgs package net weight/qty details standard pack inner carton box qty outer carton box qty gr wt size size p ac ki ng d eta il cumulative pitch error 1.0 mm/20 pitch to be measured at bottom of clinch at top of body t1 0.3 - 0.6 body width body height body thickness pitch of component feed hole pitch feed hole centre to component centre distance between outer leads component alignment tape width hold-down tape width hole position hold-down tape position lead wire clinch height component height length of snipped leads feed hole diameter total tape thickness lead - to - lead distancef1, clinch height pull - out force item a1 a t p po p2 f h w wo w1 w2 ho h1 l do t f2 h2 (p) symbol specification 4.0 4.8 3.9 6n min. 12.7 12.7 6.35 5.08 0 18 6 9 0.5 16 4 2.54 nom. 4.8 5.2 4.2 1 23.25 11.0 1.2 3 max. 1 0.3 0.4 +0.6 -0.2 0.5 0.2 +0.7 -0.5 0.2 0.5 0.2 +0.4 -0.1 tol . remarks notes 1. maximum alignment deviation between leads not to be greater than 0.2 mm. 2. maximum non-cumulative variation between tape feed holes shall not exceed 1 mm in 20 pitc h es. 3. holddow n tape not to exceed beyond the edge(s) of carrier tape and there shall be no exposure of adhesive. 4. no more than 3 consecutive missing components are permitted. 5. a tape trailer, having at least three feed holes are required after the last component. 6. splices shall not interfere with the sprocket feed holes. all dimensions in mm unless specified otherwise ammo pack s t y le adhesive ta p e on to p side flat side mechanical data t t1 t f1 f2 f p2 po do (p) w2 wo w1 w h1 a a1 p h0 l flat side of transistor and adhesive tape visible 2000 pcs./ammo pack label carrier strip 8.2" 1 3 " f e e d 1 . 7 7 " h h b 3 2 1 a k e d a a sec aa g d f f h c 3 2 1 3 2 1 all diminsions in mm. dim min. max. a 4.32 5.33 b 4.45 5.20 c 3.18 4.19 d 0.41 0.55 e 0.35 0.50 f5 deg g 1.14 1.40 h 1.14 1.53 k 12.70 ? pin configuration 1. base 2. emitter 3. collector continental device india limited data sheet page 2 of 3
disclaimer notes the product information and the selection guides facilitate selection of the cdil's discrete semiconductor device(s) best suited for application in your product(s) as per your requirement. it is recommended that you completely review our data sheet(s) so as to confirm that the device(s) meet functionality parameters for your application. the information furnished on the cdil web site/cd is believed to be accurate and reliable. cdil however, does not assume responsib ility for inaccuracies or incomplete information. furthermore, cdil does not assume liability w hatsoever, arising out of the application or use of any cdil product; neither does it convey any license under its patent rights nor rights of others. these pr oducts are not designed for use in life saving/support appliances or systems. cdil customers selling these pr oducts (either as individual discrete semiconductor devices or incorporated in their end products), in any life saving/support appliances or systems or applications do so at their own risk and cdil will not be responsible for any damages resulting from such sale(s). cdil strives for continuous improvement and reserves the right to change the specifications of its products without prior notic e. cdil is a registered trademark of continental device india limited c-120 naraina industrial area, new delhi 110 028, india. telephone + 91-11-579 6150 fax + 91-11-579 9569, 579 5290 e-mail sales@cdil.com www.cdil.com continental device india limited data sheet page 3 of 3
|
